Follow us :

How to Set the Electric Fence Post Correctly?

time2021/12/22

By reading this article, you can get a complete guide for setting up electric fence posts, so as to better apply electric fences and extend their lifespan.
a complete guide for setting up electric fence posts
The electric fence post is arranged around the fence and plays the role of connecting the electric fence line, which is an indispensable electric fence article. We can use the following steps to correctly install the electric fence, so as to make it play its due function.

General Guidelines for Post Spacing

Wood posts at least 6 inches in diameter should be used at the corners and the ends of fence lines due to the extra strain at these locations. The post should be anchored 3 to 4 feet into the ground.

Corner posts are the keys to a sturdy fence. Consider using brace posts during long runs of multiple-wired fences. Line posts need only support the wire between the corner posts.

Posts need to be placed wherever there is a high or low spot in the fence line terrain.

On hillsides, posts should be installed perpendicular to the slope. This keeps the wire at the proper height and spacing. Before you start installing your posts, we recommend visiting our electric fence planning guide.

Setting Corner, End, and Line Brace Assemblies

Corner and end posts, along with line brace assemblies, are the backbone of your fencing system. In order for your fence to stand up to the strain of a tensioned line, it is imperative that you do things right the first time and set posts deep.

Step-in, pigtail, rebar, fiberglass posts, and t-posts are not recommended for corner posts. Although they are less expensive than wood posts, they cannot hold up to the strain and tension applied to these areas of the fence.

Important things to remember when setting corner, end, and line brace assemblies:

(1) Set corner posts leaning back from the direction of the fence approximately five degrees.

(2) Corner posts require a brace assembly for each fence leading to it.

(3) With fences more than 200+ feet, it is best to use a double-span assembly.

(4) Brace wire should pull in the opposite direction than the fence is pulling.

When spans between posts exceed 650 feet use braced line post assemblies every 650 feet of the fence line. (Note: Brace line assembly is the same as a single span braced corner, but uses a second diagonal brace wire to pull the fence in the opposite direction.)

If adequate post bracing cannot be achieved, additional bracing will be required to maintain tension.

Setting Fence Posts

How you set your fence posts will depend on the type of posts you have chosen.

(1)Step-in and Pigtail Posts

These posts are easily set by stepping in or pushing the base of the post into the ground. Rebar/fiberglass posts must be driven into the ground with a rubber mallet.

(2) T-Posts and Rebar

T-posts are most effectively set by using a special tool known as a T-post pounder. You can purchase a "post pounder" from the same source where you buy your electric fence supplies. A heavy pipe with a closed-end can also work. Rebar can be pounded into the ground with a heavy hammer.

(3) Wooden Posts

Wooden posts, which will make up the end, corner, and brace posts, can be driven into the ground with a post pounder or tamped into place. An additional method to set wooden posts is to dig a hole larger than the post diameter. Place the post in the hole and then repack the soil around it. You want to make sure you center the post before tamping. This will make tamping easier and allow the soil to pack tighter around the post.

To set wooden fence posts, mark your digging tool to the desired depth fence posts will be set. This will ensure uniform depth.

A depth of 3 - 4 feet will usually work, however in sandy or rocky soil, the fence posts will need to be set deeper than in clay or dirt. Also, the amount of tension on the wire at the corner will determine the depth.

Before installing the electric fence post, we must understand the types and differences of the fence post in order to make better use. For the specific selection and installation instructions of electric fence posts, HPS Fence can provide you with a complete application guide.

With excellent R&D technology and thoughtful service, we have become one of the leading manufacturers of electric fence products. We have a professional production team and strict quality inspection system, which can carry out all-around quality control on the quality of products. At the same time, we will also provide thoughtful one-stop service according to the diverse needs of customers. If you have a demand for electric fence posts, HPS Fence is undoubtedly your best choice.